Universal Two-Part Epoxy Adhesive

SKU: BISONEPOXY-50

€8,20

Only 2 left in stock

OVERVIEW

PROPERTIES Super-strong up to 170 kg/cm² Resistant to temperatures between -40 °C and +100 °C Filling Water resistant Chemical resistant Paintable SUITABLE FOR: Suitable for repairs to metal, ceramics, porcelain, crystal, glass, pearls, precious stones and various synthetics polyester, bakelite, formica, rigid polystyrene and acrylic glass Perspex®. NOT SUITABLE FOR: Not suitable for Polyethylene PE, polypropylene PP, PTFE and silicone rubber. BEFORE USE: Working conditions Only apply at temperatures between +10 °C and +35 °C. Product cures by mixing the resin and the hardener. Personal safety Preferably wear gloves. Surface requirements The surface must be dry, clean and free of dust and grease. Preliminary surface treatment Degrease parts to be bonded with methylated spirit. Roughen smooth surfaces sandpaper. Tools Mix the components by means of the supplied mixing bowl and spatula. Mixture ratio 1:1 Coverage 1 ml = approx 10 cm² at a film thickness of 1 mm DURING USE: Handling of packaging Remove the spatula from the side of the double syringe, and the closure cap from the handle. Break the seal of the double syringe. Directions for use Press out an equal amount of both components onto the enclosed mixing tray. Mix these two equal parts well with a spatula until a mixture is obtained with a homogeneous colour. Apply the mixture, which at room temperature +20 °C remains toolable for about 1.5 hours, as a thin layer on one of the two materials. Join the materials and keep them in place for 7 hours. Be careful not to move the parts before the adhesive has cured. Resin and hardener must not come into contact with each other unless for usage. Advice Some types of synthetics can not be joined such as polyethylene and polypropylene. Use a piece of adhesive tape in order to keep the parts in place while the adhesive is curing. Points of attention After use close well note: always place back the cap in the same way, due to the bonding of the cap to the double syringe. For optimum performance it is important to create a larger amount of adhesive and mix it very well. Curing time depends on the temperature. Adhesive does not cure below +5 °C. AFTER USE: Stains/residue Remove wet stains immediately with warm water and soap. Cured adhesive residue can only be removed mechanically. Storage conditions Store in tightly closed packaging in a dry, cool and frost-free place.

  • Product: Universal Two-Part Epoxy Adhesive
Product Description

Product: Universal Two-Part Epoxy Adhesive

Description

PROPERTIES Super-strong up to 170 kg/cm² Resistant to temperatures between -40 °C and +100 °C Filling Water resistant Chemical resistant Paintable SUITABLE FOR: Suitable for repairs to metal, ceramics, porcelain, crystal, glass, pearls, precious stones and various synthetics polyester, bakelite, formica, rigid polystyrene and acrylic glass Perspex®. NOT SUITABLE FOR: Not suitable for Polyethylene PE, polypropylene PP, PTFE and silicone rubber. BEFORE USE: Working conditions Only apply at temperatures between +10 °C and +35 °C. Product cures by mixing the resin and the hardener. Personal safety Preferably wear gloves. Surface requirements The surface must be dry, clean and free of dust and grease. Preliminary surface treatment Degrease parts to be bonded with methylated spirit. Roughen smooth surfaces sandpaper. Tools Mix the components by means of the supplied mixing bowl and spatula. Mixture ratio 1:1 Coverage 1 ml = approx 10 cm² at a film thickness of 1 mm DURING USE: Handling of packaging Remove the spatula from the side of the double syringe, and the closure cap from the handle. Break the seal of the double syringe. Directions for use Press out an equal amount of both components onto the enclosed mixing tray. Mix these two equal parts well with a spatula until a mixture is obtained with a homogeneous colour. Apply the mixture, which at room temperature +20 °C remains toolable for about 1.5 hours, as a thin layer on one of the two materials. Join the materials and keep them in place for 7 hours. Be careful not to move the parts before the adhesive has cured. Resin and hardener must not come into contact with each other unless for usage. Advice Some types of synthetics can not be joined such as polyethylene and polypropylene. Use a piece of adhesive tape in order to keep the parts in place while the adhesive is curing. Points of attention After use close well note: always place back the cap in the same way, due to the bonding of the cap to the double syringe. For optimum performance it is important to create a larger amount of adhesive and mix it very well. Curing time depends on the temperature. Adhesive does not cure below +5 °C. AFTER USE: Stains/residue Remove wet stains immediately with warm water and soap. Cured adhesive residue can only be removed mechanically. Storage conditions Store in tightly closed packaging in a dry, cool and frost-free place.

Specifications

PROPERTIES Super-strong up to 170 kg/cm² Resistant to temperatures between -40 °C and +100 °C Filling Water resistant Chemical resistant Paintable SUITABLE FOR: Suitable for repairs to metal, ceramics, porcelain, crystal, glass, pearls, precious stones and various synthetics polyester, bakelite, formica, rigid polystyrene and acrylic glass Perspex®. NOT SUITABLE FOR: Not suitable for Polyethylene PE, polypropylene PP, PTFE and silicone rubber. BEFORE USE: Working conditions Only apply at temperatures between +10 °C and +35 °C. Product cures by mixing the resin and the hardener. Personal safety Preferably wear gloves. Surface requirements The surface must be dry, clean and free of dust and grease. Preliminary surface treatment Degrease parts to be bonded with methylated spirit. Roughen smooth surfaces sandpaper. Tools Mix the components by means of the supplied mixing bowl and spatula. Mixture ratio 1:1 Coverage 1 ml = approx 10 cm² at a film thickness of 1 mm DURING USE: Handling of packaging Remove the spatula from the side of the double syringe, and the closure cap from the handle. Break the seal of the double syringe. Directions for use Press out an equal amount of both components onto the enclosed mixing tray. Mix these two equal parts well with a spatula until a mixture is obtained with a homogeneous colour. Apply the mixture, which at room temperature +20 °C remains toolable for about 1.5 hours, as a thin layer on one of the two materials. Join the materials and keep them in place for 7 hours. Be careful not to move the parts before the adhesive has cured. Resin and hardener must not come into contact with each other unless for usage. Advice Some types of synthetics can not be joined such as polyethylene and polypropylene. Use a piece of adhesive tape in order to keep the parts in place while the adhesive is curing. Points of attention After use close well note: always place back the cap in the same way, due to the bonding of the cap to the double syringe. For optimum performance it is important to create a larger amount of adhesive and mix it very well. Curing time depends on the temperature. Adhesive does not cure below +5 °C. AFTER USE: Stains/residue Remove wet stains immediately with warm water and soap. Cured adhesive residue can only be removed mechanically. Storage conditions Store in tightly closed packaging in a dry, cool and frost-free place.

Packaging
Length: 0 mm
Width: 0 mm
Height: 0 mm
Weight: 0 kg